|
MAKE
|
MODEL
|
Seat
Belt Installation (Rear seat belts unless otherwise
stated)
|
| CITROEN |
BX |
Front
seat belt: Additional fitting bracket (Ref.F1) required. |
| FORD |
FIESTA
|
Front
seat belt: Mount retractor vertically. Use 2 plain spacers to clear
Ford mounting pins. |
ESCORT (Mk III or IV)
ORION |
Front
seat belt: Additional fitting bracket (Ref. D1) required
Use flat bracket supplied on L/H side to move retractor forward
(see diagram 1). |
| FIAT |
127 |
Front
seat belt: Mount retractor vertically using partly straightened
L bracket supplied. |
| MG |
MGB
ROADSTER/GT/MIDGET |
Front
seat belt: Mount retractor using Z bracket supplied. |
| MORRIS |
MINOR
SALOON |
Mount
retractor on parcel shelf |
| MINOR
TRAVELLER |
Mount
retractor Far enough forward on the wheel arch to provide sufficient
webbing length for passenger usage. |
| NISSAN |
BLUEBIRD
(86 on) |
Front
Seat Belt: Mount retractor using flat bracket and Z bracket supplied. |
| SUNNY
EST (82-86) |
Additional
fitting bracket (Ref. D1) required. |
| PRAIRIE |
Use
lower inboard anchorage points on seat base positioned behind circles
marked on trim. |
| PEUGEOT |
205 |
Remove
washer bottle for access on R/H side. Bend lip of aperture to allow
anchorage point on reel and car to be aligned. |
| 405 |
Use
Z bracket supplied and 3 plain spacers. |
| 504
(Estate/Family Estate) |
Mount
retractor externally of aperture. |
| 505
(Estate/Family Estate) |
Mount
retractor externally of aperture. |
| RENAULT |
11 |
Mount
retractor externally of aperture on R/H side.
Cut plastic side support shelf. |
| ROVER
GROUP |
MONTEGO
SALOON |
Additional
fitting bracket (Ref. D1) required. |
| 213/216
(to 86) |
Mount
retractor above parcel shelf. |
| 213/216
(86 on) |
Mount
retractor above parcel shelf. |
| SKODA |
ESTELLE |
Ensure
bolts do not foul petrol tank. |
| VAUXHALL |
ASTRA
HATCHBACK (to 84) |
Mount
retractor externally of aperture |
| ASTRA
HATCHBACK (84 on) BELMONT |
Pass
retractor through aperture close to rear light cluster and move
forward to anchorage point. |
| ASTRA
ESTATE |
Mount
retractor externally of aperture. |
| VOLVO |
3
SERIES (3 door) |
Front
Seat Belt: Mount retractor externally of pillar using partly straightened
L bracket supplied. |
|
GENERAL
NOTES
|
NB:
Before proceeding ensure there is sufficient clearance for bolts,
nuts etc.
- Most
lower anchorages points for rear belts are under the seat. These
will normally be covered by removable plugs / bungs.
- It
may be necessary to remove trim to reveal upper anchorage points.
-
Some vehicles require a slot to be cut in the parcel shelf to
thread webbing through. The position is usually marked on the
underside of the shelf.
- Some
estate cars require the car manufacturer's vertical bars across
the rearside windows for correct installation.
- Front
Seats may have to be removed to gain access for mounting a 15cm
buckle assembly.
- The
222 'All Ages' seat belt conversion kit can be fitted to existing
or replacement lap and diagonal seat belts, front or rear. This
kit enables the belt to be used by occupants from the age of
4 years upwards.
- When
anchorage points are created reinforcing plates should be used.
These points will afford some level of safety.
- The
technical department is available Monday to Friday, 9.00am -
4.30pm to provide further advice. Additional fitting brackets
are free of charge.
|
